Understanding Thyristor SCR Specifications & Parameters

 Understanding Thyristor SCR Specifications & Parameters

We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

When choosing a thyristor or SCR, there are several datasheet parameters that need to be understood so that the correct device can be selected.

The various SCR / thyristor datasheet specifications and parameters are rather different to the more familiar transistor and FET specifications, but even so they are relatively straightforward.

It is worth noting that many of the thyristor specifications are also applicable for TRIACs and DIACs as well.

Common Thyristor Specifications & Datasheet Parameters
SpecThyristor Specification / Parameter Details
dI/dtMaximum rise of on-state currentThere is a maximum rate of rise for the on-state current during turn on. If this rate is exceeded then the device can be damaged.
IGMPeak gate currentThis is the maximum level of gate current that should not be exceeded.
IGTGate trigger currentThis is the current required in the gate to enables the device to be triggered and to latch in its on-state provided there is sufficient anode cathode current to maintain the current flow.
I2tOvercurrent protectionThe I2t parameter indicates the fuse that is required for protection. It is for the 10ms overcurrent duration.
IT(AV)Average on-state currentThis parameter is different to the RMS current as it defines the average current rather then the RMS. RMS will give the true heating effect of the current.
IT(RMS)RMS on-state currentThis thyristor specification is the maximum allowed RMS current through the device. It is specified for a given temperature. Different datasheet specifications may quote ambient temperature, Ta, case temperature, Tc, or even the lead temperature, Tl. The method used for quoting the temperature normally depends upon the type of case used for the thyristor / SCR.
ITSMNon-repetitive surge on-state currentAs the name implies this datasheet parameter for thyristors defines the maximum peak current in the device under pulse conditions. It is necessary to look at the exact conditions for the manufacturer in question, but it is often defined for a half sine wave. The duration is specified for 50 Hz (10ms duration) and 60Hz (8.3ms duration). It is required because a surge current exceeding the maximum may cause failure of the device.
TJJunction temperatureThis is the junction temperature and often the maximum junction temperature is specified in the datasheets. Calculating the thermal resistance it is possible to determine the conditions under which the maximum junction temperature is not exceeded.
TstgStorage temperatureThis is the minimum temperature in which the device can be stored.
VDRM / VRRMRepetitive peak off-state voltageThis parameter is the maximum peak voltage that is allowed across the device. This datasheet specification parameter should not be exceeded otherwise the device may fail. It is also always good to leave sufficient margin to allow for transients. This parameter is specified for conditions up to the maximum junction temperature. Also leakage currents (IDRM / IRRM) are also normally defined under this datasheet specification.
VGTGate trigger voltageThis is the voltage that needs to be applied between the gate and cathode to enable the gate trigger current to be reached and the device to fire.
VRGMPeak reverse gate voltageThis is the maximum level of gate voltage that can be applied across the gate cathode junction without the possibility of damage resulting. It is wise to operate well below this voltage.

Whilst there are many other thyristor specifications and parameters that are used in their datasheets, these are some of the more widely sued ones which are needed in the deign of circuits and selection of the right components.

Watch the video: How does a Thyristor work? (June 2022).


  1. Caw

    Came by chance on the forum and saw this topic. I can help you with advice.

  2. Norris

    You are not right. Enter we'll discuss. Write to me in PM, we will handle it.

  3. Gardakinos

    Bravo, what excellent answer.

  4. Shakagar

    This is far from news, I read about it a couple of months ago.

  5. Chogan

    Definitely the perfect answer

  6. Blade

    the sure-fire answer

  7. Koen

    In my opinion you are wrong. I can defend my position. Write to me in PM, we'll talk.

Write a message